Why Boerne Homeowners Choose Reflectix Insulation
We provide independent Boerne Reflectix service, specializing in radiant barrier repair, replacement, and hybrid attic systems that combine Reflectix products with proper air sealing and insulation. As an independent Reflectix service provider - not affiliated with or authorized by Reflectix Inc. - our recommendations are based solely on what performs in Boerne’s Hill Country climate, not on manufacturer quotas. Call (830) 529-7780 for a free estimate.
Reflectix radiant barriers and double reflective insulation rolls are common sights in Boerne attics, especially in the master-planned subdivisions along I-10 and near Esperanza where builders spec’d them as cost-effective heat-gain reduction. The metal roofs on those Hill Country-style homes supercharge radiant heat, and Reflectix can work - but only when it’s installed with adequate ventilation, clean surfaces, and realistic expectations about R-value. We’ve pulled down hundreds of square feet of failed Reflectix in Kendall County homes where the product was doing more harm than good, and we’ve installed it correctly in hundreds more where it performs as designed. Wes Okafor, our owner, learned the trade at Olive-Harvey College in Chicago and has been running blower-door tests on every job for going on eighteen years. He’ll tell you flatly: “Seal the envelope first. Then fill it.” A radiant barrier stapled to a rafter in an unsealed, unventilated attic is just shiny wallpaper.
Why Trust Topside Attic Insulation Boerne for Your Reflectix Insulation?
We know the Reflectix product line cold. We’ve handled the BP24010 Double Reflective Insulation Roll, the wider BP48010, the perforated RB48125 Radiant Barrier, and the RFOIL48125 Reflective Insulation Roll in attics across Boerne and Reflectix Insulation in Scenic Oaks, TX - from the 2000s-era production homes near the Cibolo Nature Center to newer builds in the I-10 corridor. Each has its place, and each has its failure mode. We don’t guess which one you’ve got; we inspect, measure, and test.
Our crews stock genuine Reflectix rolls and perforated radiant barrier products from authorized distributors, but we’re not locked into any single brand. When a Reflectix-only installation has failed, we assess whether a targeted repair or full replacement with a hybrid system makes more sense for your home’s specific heat gain and moisture profile. That independence matters in Boerne, where the elevation at 1,400 feet drives larger temperature swings than San Antonio below, and where Winter Storm Uri proved that insulation performing at both extremes isn’t optional.
Every Reflectix job we take starts with a written price and a written scope - Haven Standard Clause 1 - and ends with a Documented Photo Record. On applicable jobs, you’ll get before-and-after blower-door readings in pascals, printed, so you can see the pressure differential in black and white. No claim without a number. That’s how Wes has run this shop since 2016.
Common Reflectix Insulation Problems We Fix in Boerne
- Condensation and mold on perforated RB series barriers. The Reflectix RB48125 Radiant Barrier Perforated Roll is designed to allow moisture passage, but in Boerne attics without adequate ventilation - especially in the tight, complex rooflines of Hill Country-style homes - humid air still condenses on the reflective surface. We’ve found mold growth on adjacent roof decking in multiple Esperanza-area homes where the barrier was installed without soffit and ridge vent balance. The product wasn’t defective; the system around it was.
- Trapped heat in BP series double reflective rolls used as standalone attic floor insulation. The Reflectix BP24010 and BP48010 Double Reflective Insulation Rolls are radiant barriers, not bulk insulators. When older Boerne homes - including some mid-century structures near Main Street’s historic core - use these as the only attic floor insulation, heat gets trapped between the reflective layers and the living space below. R-value performance collapses, and cooling loads spike. We see this most in homes where a previous owner or handyman misunderstood the product’s purpose.
- Torn and flaking edges from thermal cycling. Reflectix radiant barrier stapled to roof rafters with exposed edges suffers in Central Texas attics. Daily temperature swings of 40°F or more in Boerne’s dry climate cause the material to expand and contract. Over two or three years, the edges tear, the reflective coating flakes, and the barrier becomes a source of attic debris rather than heat rejection. Metal roofs make this worse by amplifying the temperature extremes.
- Reflective layer degradation over dirty or compacted existing insulation. When Reflectix products are installed over existing blown-in fiberglass that’s settled, stained, or rodent-damaged - common in Boerne’s dry conditions where fiberglass settles faster than in humid climates - the reflective surface loses effectiveness and the underlying insulation compacts further. The homeowner gets the worst of both: a radiant barrier that can’t reflect and bulk insulation that can’t insulate.
- Blocked ventilation causing heat buildup behind barrier. A Boerne homeowner called us after their attic hit 140°F even with a Reflectix BP48010 radiant barrier stapled to the rafters. We found the barrier was trapping heat against the roof deck because the ridge vents were blocked by old insulation, and the perforations were clogged with dust. Our crew removed the failing barrier, air-sealed the attic floor, and installed a properly ventilated radiant barrier system with new soffit baffles, dropping peak attic temps by 25 degrees. The product wasn’t the problem. The installation was.
Reflectix Parts & Our Repair-vs-Replace Approach
We source genuine Reflectix rolls and perforated radiant barrier products from authorized distributors, but for most attic and crawl space applications we pair them with high-performance blown-in or spray foam insulation to create a complete thermal envelope. A radiant barrier alone - any radiant barrier - only addresses radiant heat transfer. In Boerne, where conduction and convection matter just as much, a hybrid system with Attic Insulation services almost always outperforms a Reflectix-only approach.
Our repair-vs-replace decision is straightforward. If your Reflectix barrier is intact, properly positioned, and merely underperforming due to poor ventilation or air leakage, we’ll repair the system: clear the vents, seal the envelope, reinstall. If the material is torn, mold-stained, or installed over failed bulk insulation, replacement with a hybrid radiant barrier plus insulation system is usually the better investment. We stock Reflectix BP and RB series products locally for fast turnaround, and we carry Owens Corning, Johns Manville, Knauf, Rockwool, and spray foam options for the insulation component. You’ll get a written price for either path before anyone lifts a tool. Call (830) 529-7780 and we’ll walk through what your attic actually needs.
Our Reflectix Service Process - Step by Step
- 1
Diagnosis with blower-door and thermal imaging. We pressurize your home with a blower-door test - a pressurization reading that shows, in one number, how much air your building envelope is losing - and run thermal imaging to locate air leakage paths and insulation gaps. For Reflectix systems, we specifically check attic ventilation flow, barrier surface condition, and whether the reflective layer has degraded.
- 2
Written scope and price. Under Haven Standard Clause 1, you get a flat price, written scope, and written warranty before anyone starts. No exceptions. If we’re repairing a Reflectix RB48125 installation, the scope specifies ventilation corrections. If we’re replacing with a hybrid system, it names every material and its R-value contribution.
- 3
Air sealing first, then insulation. We seal top plates, can lights, penetrations, and bypasses before any insulation goes in. A radiant barrier over an unsealed attic floor is just reflecting heat into a leaky box. This step is non-negotiable for us.
- 4
Reflectix repair or hybrid installation. For repairs, we clean, reposition, or replace specific Reflectix sections and restore ventilation. For hybrid systems, we install properly ventilated radiant barrier with soffit baffles and pair it with blown-in or spray foam insulation to address all heat transfer modes.
- 5
Blower-door verification and documentation. We run the blower-door test again and hand you a printed pressure-differential report in pascals. You’ll also receive a Documented Photo Record of the completed work. Our 365-Day Done Right Promise applies to all completed work - if it’s not done right, we make it right.
Reflectix Products We Service & Install in Boerne
We work with the full Reflectix residential line: BP24010 Double Reflective Insulation Roll (24 in x 10 ft), BP48010 48 in x 10 ft Double Reflective Insulation Roll, RB48125 Radiant Barrier Perforated Roll, and RFOIL48125 Reflective Insulation Roll. We stock BP and RB series products locally for repair jobs, and we source RFOIL and specialty sizes as needed. For Boerne’s metal-roof homes and high-radiant-gain attics, we most commonly install the RB48125 as part of a hybrid system with air sealing and blown-in insulation - never as a standalone solution. We also handle full Reflectix Insulation in Fair Oaks Ranch, TX and surrounding areas, plus Attic Insulation Removal when existing Reflectix or underlying insulation has failed beyond repair.
We Also Service These Brands
We’re not a single-brand shop. Our crews are trained on Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber systems. Whether you need spray foam, mineral wool, or a different radiant barrier brand entirely, we install and service it to the same standard: sealed first, then insulated, with numbers to prove it.
FAQs - Reflectix Insulation Service in Boerne
Is Topside Attic Insulation Boerne authorized by Reflectix?
No. We are an independent Reflectix service provider, not affiliated with or authorized by Reflectix Inc. This independence means our recommendations are based on what actually works in your Boerne home, not on manufacturer quotas or exclusive product lines. We source genuine Reflectix products when they’re the right choice, and we recommend alternatives when they’re not.
Do you use genuine Reflectix/OEM parts?
Yes, we source genuine Reflectix rolls and perforated radiant barrier products from authorized distributors for repairs and targeted replacements. For most attic and crawl space applications, we pair them with high-performance blown-in or spray foam insulation from Owens Corning, Johns Manville, Knauf, or other manufacturers to create a complete thermal envelope. Call (830) 529-7780 to discuss what’s right for your home.
How long does Reflectix service take?
Most Reflectix repair jobs in Boerne take one day. Full replacement with a hybrid radiant barrier plus insulation system typically takes one to two days, depending on attic size and whether we need to remove failed existing insulation first. We arrive on schedule, you get a named technician and a text when they’re on the way - that’s Haven Standard. Call (830) 529-7780 to check availability.
What Reflectix models/series do you cover?
We service and install the BP24010 Double Reflective Insulation Roll, BP48010 48 in x 10 ft Double Reflective Insulation Roll, RB48125 Radiant Barrier Perforated Roll, and RFOIL48125 Reflective Insulation Roll. We also handle custom-cut applications and hybrid systems combining Reflectix with other insulation types. If you’re not sure what you have, we’ll identify it during inspection.
Will service void my Reflectix warranty?
Reflectix product warranties are typically limited to manufacturing defects and don’t cover installation-related issues, which are the most common failures we see in Boerne. As an independent service provider, our work doesn’t activate or void any manufacturer warranty - it simply addresses the installation and system performance problems that warranties rarely cover. We provide our own 365-Day Done Right Promise on all completed work.
How much does Reflectix insulation cost in Boerne?
Reflectix repair jobs in Boerne typically run $800-$1,800 depending on attic size and ventilation corrections needed. Full hybrid radiant barrier replacement with air sealing and blown-in insulation ranges from $2,400-$5,500 for most homes in the Esperanza and I-10 corridor areas. We provide a written price before any work starts - always - and we offer a Free Second Opinion on any written estimate you’ve already received. Call (830) 529-7780 for an exact quote; estimates are free.
Does Reflectix radiant barrier work as a standalone attic insulation in Boerne?
No. Reflectix radiant barriers address radiant heat transfer only. In Boerne’s climate - with 95°F+ summers, hard freezes, and large diurnal temperature swings at 1,400 feet elevation - conduction and convection matter equally. A standalone radiant barrier without bulk insulation and proper air sealing will not keep your home comfortable or your bills reasonable. We install Reflectix as part of hybrid systems, never alone.
What is the difference between Reflectix BP24010 and Reflectix RB48125?
The BP24010 is a double reflective insulation roll with internal bubble layers, designed for duct wrap, crawl space walls, and similar applications where some R-value and vapor resistance are needed. The RB48125 is a perforated radiant barrier roll, designed specifically for attic applications where moisture must pass through to prevent condensation on the reflective surface. Using the BP series in an attic floor or the RB series in a crawl space without understanding the moisture dynamics is a common mistake we correct in Boerne homes.
Can you install Reflectix over existing blown-in insulation in my attic?
Only if the existing insulation is clean, uncompressed, and dry. In Boerne’s dry climate, blown fiberglass settles faster than in humid regions, and we’ve found many attics where the underlying insulation is already below spec. Installing Reflectix over failed bulk insulation traps heat and masks the real problem. We inspect first, remove when necessary, and start with a clean, sealed attic floor.
How do I know if my Reflectix radiant barrier is failing in a Boerne home?
Signs include attic temperatures above 130°F in summer despite the barrier, visible tears or flaking on the reflective surface, mold staining on adjacent wood, and cooling bills that don’t reflect the promised performance. The definitive check is a blower-door test combined with attic ventilation measurement - we offer this as part of our free estimate. Call (830) 529-7780 to schedule.
Do you offer Reflectix installation in crawl spaces or only attics?
We install Reflectix in both locations, but the product choice and installation method differ. In crawl spaces, we typically use BP series double reflective insulation on walls or rim joists, paired with vapor barrier and air sealing. In attics, we use RB series perforated radiant barrier as part of a hybrid ventilation and insulation system. Boerne’s limestone slab-on-grade foundations create specific moisture conditions in crawl spaces that we account for in every installation.
Book Your Reflectix Service in Boerne, TX
Call (830) 529-7780 to schedule your free estimate. A live person answers 24/7 - no voicemail loops, no callback windows measured in business days. You’ll get a written price before any work starts, a named technician who arrives on schedule, and documented proof of the results when the job is done. That’s the Haven Standard, and it’s how we’ve handled 9,000+ homes since 2016.
Written by Wes Okafor, Owner at Topside Attic Insulation Boerne, serving Boerne since 2016.